Gerber GS750 User Manual download pdf (Page 45)

OPERATION

Power Up

When the GS750

plus

is turned on, the following sequence occurs:

1. A short beep sounds, the Power light comes on, and the RUN

CONT, RUN SING and SWIVEL KNIFE lights blink.

2. As the GS750

plus

performs self-check tests, the lights over the

RUN and SWIVEL KNIFE keys flash, and an additional beep

sounds.

3. When the self-check is complete, the lights blink and a beep

sounds.

4. The plotter goes off-line in tangential knife mode. Only the

Power light remains on. This is the initial setting at power-up.

Note: Rapid, continuous beeping and flashing lights may signal a

self-check error. See the "Error Conditions" section for more

information.

1 2 ... 40 41 42 43 44 45 46 47 48 49 50 ... 82 83

COPYRIGHT NOTICE 3
FCC NOTICE 5
TABLE OF CONTENTS 7
INTRODUCTION 9
Convenience 10
Support Information 10
About This Manual 11
Conventions 12
PACKAGE CONTENTS 13
BOX 3: Paper 14
BOX 4: Vinyl 14
INSTALLATION 15
Mount Tool Rack 17
Mount Roll Support Bars 17
Install Plotter on Stand 17
Mount the Material 18
Plotter Work Area 18
Connect to the Plotter 18
Communication Parameters 19
Power Cords 20
Power-up Sequence 20
Plotter Selection 21
Add Plotters 22
Delete Plotters 23
Assign Default Plotter 23
MATERIALS AND TOOLS 25
18 GS750 26
To feed and align material 27
HELPFUL HINTS 28
Tool Force Dial 29
Plotter User Reference Card 30
ADJUSTMENTS 30
Plotter User 30
Reference Card 30
TOOLS AND TOOL HANDLING 31
Pen Holder and Pens 32
PEN REPLACEMENT 33
To replace a pen 33
Pounce Wheel Holder 34
OFF-CENTER HOLES 35
PLOTTER SPEED 35
GRAPHIX ADVANTAGE Reference 35
POUNCE WHEEL REPLACEMENT 36
To replace the pounce wheel 36
Knife Holder and Blades 37
KNIFE HOLDER INSTALLATION 38
To install a knife holder 38
Plotter User Reference 38
Suggested Tool Force Settings 39
BLADE REPLACEMENT 40
Tools and Tool Handling 33 41
34 GS750 42
Tools and Tool Handling 35 43
OPERATION 45
Front Panel 46
Operation 39 47
40 GS750 48
Operation 41 49
Single Plot Exercise 50
RUN CONTINUOUS KEY 50
To plot in continuous mode 50
Operation 43 51
RESET KEY 52
To cause an emergency stop 52
To clear an error signal 52
To access diagnostics 52
SPECIAL DIAGNOSTICS 53
Diagnostic Options 54
WAGON WHEEL TEST PLOT 55
SQUARE/CIRCLE TEST PLOT 56
ERROR CONDITIONS 57
ERROR CODES 58
MAINTENANCE 59
CARRIAGE AND BALL BUSHING 60
SPROCKETS AND BAIL ARMS 61
Do not oil excessively 61
Fuse Replacement 62
PLOTTER ADJUSTMENTS 63
LEFT COVER 64
Troubleshooting Guide 65
SYMPTOMS 66
OBJECTIVE 66
ADJUSTMENT PROCEDURE 66
Plotter Adjustments 59 67
60 GS750 68
62 GS750 70
Plotter Adjustments 63 71
64 GS750 72
X Axis Backlash Adjustment 73
66 GS750 74
Plotter Adjustments 67 75
Y Axis Backlash Adjustment 76
Plotter Adjustments 69 77
11. Replace the cover 78
PLOTTER USER REFERENCE CARD 79
PLOTTERERRORCODES 80
APPROXIMATE GS750 80
TOOL FORCE SETTINGS 80
76 Index 82
P57348A Rev A 83

Comments to this Manuals

No comments

Gerber GS750 User Manual Page 45

Comments to this Manuals

Related products and manuals for Unknown Gerber GS750